The valve is made of flexible rubber, and all water exiting the dishwasher flows past the valve, moving it out of the way.
Suggested site content and search history menu, Samsung Replacement Vane-Check Drain For Dishwasher, Part# DD66-00045A, General Electric Replacement Check Valve For Dishwasher, Part# WD01X10177, General Electric Replacement Dishwasher Check Valve Drain Body, Part #WD22X10025, Account Change Pump sump check valve used on some Dishwashers. Check the following items in order to identify and correct the issue. 
Please remove them. 
Should there be any standing water left in the sump? It's right inside the nipple where the drain hose from the dishwasher attaches to the disposal. JavaScript must be enabled in order for you to uses this site. Remove the check valve using needle-nose pliers. Try running the garbage disposal (if you have one)if it shares the same drain as the dishwasher, this can prevent the dishwasher from draining. Request, California Replace the lower wash-arm support and filter assembly, then secure using the screws that were originally removed. 
This item has been successfully added to your list. https://hdsupplysolutions.com/ProductDisplay?urlRequestType=Base&catalogId=10054&categoryId=10401&productId=1476812&urlLangId=-1&langId=-1&top_category=&parent_category_rn=&storeId=10051. Terms // Leaf Group, Repair Clinic: Dishwasher Check Valve Replacement, Appliance Aid: GE Built Dishwasher, Some Draining Trouble Makers. On a Whirlpool dishwasher, the valve is located in the bottom of the inner cavity, and prevents water from flowing back into the dishwasher after it has drained. The check valve on your Whirlpool dishwasher is an important part of the dishwasher's drainage system. This Whirlpool Check Valve For Dishwasher is compatible with Whirlpool brands. Dishwasher not draining, or draining too slowly? The lower rack can simply be lifted out of the dishwasher. Check to make sure the last wash cycle completed properlyif your dishwasher has a Clean indicator light, it should be illuminated. Accessibility, Cause 5: Garbage disposal incorrectly installed, Questions other people have asked about this, Does not drain the water at the end of cycle, Dishwasher is draining slowly , and not completely draining.
Privacy, Fine If there are no obstructions to the drain system and your dishwasher is still filling with water, you may need to replace the pump. If you recently installed a new garbage disposal, make sure the knock-out plug was removed. Check the drain hose that runs from the bottom of your dishwasher to the drain pipe (usually below the sink). Enable JavaScript by changing your browser options, and then try again.
Its a one-way valve, allowing water to drain but not return to the dishwasher. He has written for the Consumer Search website and the U.S. Attorney's Office for the Middle District of Florida. The check valve is located underneath the dishwasher, just before the drain hose. What to do when your Whirlpool dishwasher won't drain properly? The maximum number of products that can be compared is 4. Whirlpool Replacement Check Valve For Dishwasher, Part #wp8268375. Try these fixes first. Remove the screw on the round pump-inlet protector, located to the left of the foreign-object protector. Pull the assembly straight out of the dishwasher. Disconnect power to the dishwasher by turning off the breaker in your fuse box. If not, the wash cycle may have been interrupted. Remove the pump-inlet protector. Make sure its not pinched or kinked. (Remember, there's still water in the unitso put a drain pan under it before removing the hose.). One or more part # you entered is invalid. Todd has a Bachelor of Science in criminal justice from the University of Central Florida. Open the door of the dishwasher, then remove the lower rack.
Place the lower rack back into the dishwasher, then close the door and restore power to the appliance to complete the replacement of the check valve. How to Remove a Spray Arm from a Whirlpool Dishwasher, How to Remove a Filter From a Maytag Dishwasher, How to Troubleshoot Error Code 1 on a Bosch Dishwasher, How to Access the Chopper System in a Whirlpool Dishwasher, Copyright 2022 Leaf Group Ltd. / Leaf Group Lifestyle, All Rights Reserved. Print & Catalog Icons. Remove the drain hose from the dishwasher (remembering to put a drain pan underneath) and check to make sure the valve is clean and opens correctly. *FREE, next-day delivery on most orders to most areas. Remove the screws located in the area that was covered by the lower wash arm, consisting of the lower wash-arm support and water-filter assembly. This Part #wp8268375 replaces 8268375, 8268389, 939846, AP3152971, PS650760. Your session is about to timeout due to inactivity.
Click OK to extend your time for an additional 0 minutes. Andrew Todd has been writing since 2006. 2022 iFixit Licensed under Creative Commons Privacy Remove the drain hose end from the nipple it's connected to below the sink or disposal, put the end in a bucket, then fill and drain the dishwasher to see if a garbage clog will simply blow out. If that doesn't work, but you see a small dribble of water, you may have to pull the dishwasher out and remove the drain hose in order clean it out or replace it. After regular wash cycles, the rubber may begin to break down, and the check valve should be replaced so that dirty water does not contaminate your dishes after the rinse cycle.
Remove the lower wash arm. Reconnect the tub on the back of the wash arm with the water-supply tube, ensuring that they snap into place. If its not removed, the dishwasher cant drain properly. Whirlpool Dishwasher stops after filling with water, LG Dishwasher Water not draining fast enough, OE error code. Locate the check valve, located on the right side of the area covered by the pump-inlet protector. Whirlpool dishwashers are susceptible to a range of issues that can cause this problemsome simple to fix, some not. Insert the new check valve using the needle-nose pliers, then replace the pump-inlet and foreign-object protectors, securing both with the screws that were originally removed. Request, Fine Print If necessary, replace it with a new hose. Place the lower wash-arm assembly into place, then rotate counterclockwise to secure. Lift the tab on the water-supply tub on the back of the bottom assembly, then rotate the assembly clockwise to release the wash arm on the bottom of the dishwasher. However, it seems JavaScript is either disabled or not supported by your browser. How do I get an awful, rotten smell out of my dishwasher? Please refine your selection. & Catalog Icons, Account Change Remove the screws securing the foreign-object protector, located at the front of the drain assembly, then pull the foreign-object protector out of the dishwasher. Close the door and press the Start button.